12/26/2023 0 Comments Windows 10 app switch to desktop mode![]() Tap a letter on the All Apps list to go to a letter chooser and quickly jump to another section. In Tablet Mode, you can also swipe up on the left side to open the All Apps menu, so you can browse your entire apps list. You can quickly test this by temporarily setting your monitor sleep time to 1 minute.This menu is joined by a Power button (which enables you to restart, shut down or sleep) and another icon at the bottom so you can scroll down through a list of app your apps, not just the ones that are pinned to the Start menu. Uninstall all greyed out monitors (even non-PNP and PNP monitors)Īfter doing this my windows don't resize after my monitor goes to sleep.Keep only the highlighted monitor you are currently using. Right-click on these monitors and select uninstall. I uninstalled ALL the greyed out monitors. I believe these are aliases to your current monitor (at a lower resolution) before Windows installed drivers for it. You may see monitors with "non-PNP" and "PNP" listed as well. When you expand the Monitors you will see your current monitor (highlighted) and all the disconnected monitors (greyed out). Start the Control Panel as Administrator: So, if you enable "Show hidden devices" in the Device Manager you will see all the monitors that were connected to your system. This includes the basic monitor support during the OS install. It appears Windows 10 keeps a history of all the monitors it encounters during its life time. ![]() I think I may have a solution for this problem. Also, installing the driver seems like a stronger action to me. Or maybe what fixed it for me was deleting the old monitors, as per Stephen's instructions. Once I went to LG's website, downloaded and installed the drivers, I stopped having the problem (tested with 1-minute sleep). Now, I don't remember installing manufacturer drivers for my other monitors, buy maybe I did when I installed them. I was deleting old unused monitor devices ("Show hidden devices") when I realized my primary monitor (the newest) was the only one without a proper driver. I copy-pasted Stephen's solution in the end of this post, since no one seems to have done it yet. I found the definitive solution to this: do as Stephen, ( st99), says here in the ninth answer – Soldeplata Saketos (at 8:48 ) When I went about following the instructions for the (highly voted) comment below, I noticed in Device Manager one of my monitors was "Generic PnP Monitor". I have three monitors and this problem was driving me nuts (actually irking me every time I woke my PC, and then I'd forget about it). The solution for me was to simply install drivers for my newest monitor. The forced resolution will override detection of the screen and should persist through sleep. However if this is unavailable, you can use the Windows Resolution window to detect devices while the monitor is disconnected, then select the display which will report “Another Display Not Connected”, then under Multiple Displays, you can drop down and select “Try to connect anyway” which will broadcast a signal to the monitor over the port type you have selected (the signal will not be interactive), then connect the display which should interpret the signals sent to it properly. You can usually force the detection of a monitor within the graphics driver control panel. If the issue is still not resolved after updating the drivers, it may be due to an unusually reported display ID (EDID). Update your graphics drivers from the manufacturer to resolve the issue. Usually this will be caused by the graphics driver not properly supporting sleep modes and therefore disabling the ability to detect a connected display when the computer goes to sleep. I don't know why there are three configs, I have only ever used one So for some reason one of the configs does not get set correctly. Moving/resize issue returned, but the lower right corner was set to I changed these to 1600x900 and the problem was solved.įurther I changed resolution (via control panel) to 1920x1080, the ![]() The third ( SIMULATED.) were set to 1024x768. Were 1440x900, so they were not involved. Under 00 was another branch also called 00. HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\GraphicsDrivers\Configuration That Windows was accessing the following Registry path: ![]() Using Sysinternals ProcessMonitor I found This fixes the issue for me now all my window positions and sizes are preserved. When waking from sleep, all my windows had been pushed to one display, and some of them resized. I'm running Windows 8.1 with two 2560x1440 displays on DisplayPort. This is an old question, but if anyone arrives here with the same issue, I suggest trying the solution posted here: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |